Files
cantabile-ha-addons/cantabile_edge/CHANGELOG.md
T

5.8 KiB

Changelog

Versions are 0.1.<n>: n counts the commits of the Cantabile repository the add-on was built from. The image's label org.opencontainers.image.revision names the commit; the agent inside is the Edge Agent image of that commit.

0.1.x

  • The Devices page is clearer: the devices you use with Cantabile are a short list, each with its state in words ("In use · reading on · control on" or "Added · reading off"), its main values now ("21.5 °C, set to 22 °C, heating") and whether it is protected. Open a device to change it: reading and control switch at once, what it reads is said in plain words ("room temperature (Living room), setpoint, heating/cooling state"), and heating or cooling, room and window, indoor or outdoor and protection each save on their own (Save shows once you change something). Removing asks you to confirm. "Untested" profiles are marked with a small badge and an "i" that explains it. Devices you can still add are listed apart, below; a device in use is never offered again.

  • Heat is shown as heat: a heat meter's or heat pump's heat is "Heat from the building (thermal)" or "Heat delivered (thermal)", in kW and kWh, in its own band below solar, home, grid and battery, never added to the electricity. With your own heat pump its electric power and its COP are shown beside the heat.

  • Blinds, curtains, shutters and awnings: the Devices page offers any of Home Assistant's covers (never a garage door, gate, door, damper or window). You set the room it shades and which way the window faces. Cantabile then moves it by the sun: in summer it closes it (partly, while someone is home) when the sun is on that window and the room is warm or dear hours are coming, and opens it again when the sun has gone; in winter it opens it for the sun's warmth and closes it in the evening to keep the warmth in, never opening it in the dark. It never moves between 22:00 and 07:00, at most once in 30 minutes, and after you move it by hand it waits 4 hours. A new shade is protected: Cantabile does not move it until you allow that on the Devices page (and only with your consent to control, in auto mode). On the dashboard it is a tile with its position slider (open and close for one without positions), and "Coming up" says what is next in words ("Bedroom curtains: close to 30 % at 14:00, sun on the west facade").

  • Temperature and humidity sensors: any such sensor (ESPHome, Zigbee, Bluetooth) that has no profile of its own is offered, never Home Assistant's or a device's own system temperatures. You choose indoor (which room; a room that has a temperature already gets a second one) or outdoor: then it is Cantabile's outside temperature, before the weather service's. On the dashboard each is a small card with its temperature and humidity.

  • Weather: a weather service (met.no, OpenWeatherMap and others) is offered as "Weather (forecast)": its hourly forecast plans solar, heating, cooling and the shades, its temperature and humidity are the outside's where no outdoor sensor measures them. With several, you choose the one Cantabile plans with.

  • Your consent at installation, in the add-on's configuration: sharing energy data with Cantabile (needed: without it the add-on does not connect, and its page says why) and, separately, control. The same texts and version as a Cantabile Hub's setup; recorded with when and how it was given and sent to Cantabile. With it, reading and control are switched on per device on the Devices page.

  • Both of the add-on's pages (Devices, Building or community) are for Home Assistant's administrators only.

  • The add-on's page "Devices": Home Assistant's devices with the Cantabile device profile that fits each (specific profiles first, the generic thermostat otherwise), what Cantabile would read and could control, and Use with Cantabile: the device's mapping from its profile with reading and control off, its protection as the profile says (the owner lifts or sets it), heating or cooling for a thermostat that does both. The proposal leaves a used device to its profile. The device appears on Cantabile's dashboard and in the area "Cantabile" (without an area of its own). The page and "Building or community" are one app, linked from the dashboard; only Home Assistant's administrators can use them.

  • The add-on's page in German or English, as the browser asks (Home Assistant's own language is not changed).

  • A reinstall is recognised: the add-on sends hashed hardware ids with its enrolment (no serial leaves Home Assistant in clear). When Cantabile merges it into the home's earlier site, it keeps that site, and its page offers the earlier consents for the building's and the community's operator again, given only with your yes.

  • One dashboard "Cantabile" with views (overview, energy, heating & cooling, devices, building) instead of one dashboard per subject; the add-on's page leaves the sidebar and is linked from the dashboard.

  • A mapping at the first start, proposed from Home Assistant's devices and Cantabile's device profiles, and the import of an earlier install's mapping from /share/cantabile/mapping.yaml; consent always off.

  • First packaging as a Home Assistant add-on: the agent and its link to Cantabile, the MQTT broker from the Mosquitto add-on, Cantabile's area, device and dashboards in Home Assistant.

  • The add-on's page: "Building or community". A home in no building joins an energy community with a code or asks one nearby, after seeing its rules, and chooses whether its operator receives the home's data.

  • A community's rules on that page include the price of shared energy, its amounts and penalties where set, and the notice period.


© 2026 Setti Solutions S.R.L, www.setti.md. All rights reserved.